Uncoded items are applicable to all models. Identifi-
code (first four digits). For example FSN
6625-553-0142 converts to NSN 6625-00
cation of the usable on codes used in this publication
are --
553-0142.
c. Description. Indicates the Federal item name
Code
Used on
and a minimum description required to identify the
ANA
TA-264/TP
item. The last line indicates the reference number
ABO
TP-9
followed by the applicable Federal Supply Code for
b. The following publications pertain to the
Manufacturer (FSCM) in parentheses. The FSCM is
equipment and its components:
used as an element in item identification to designate
TM 11-2059
Telephone TP-9 and Telephone
manufacturer or distributor or Government agency,
Set TA-264/PT.
etc., and is identified in SB 708-42.
TM 11-5805-291-20P Organizational Maintenance
d. Unit of Measure (U/M). Indicates the standard
Repair Parts and Special
or basic quantity by which the listed item is used in
Tools List: Telephone Set
performing the actual maintenance function. This
TA-264/PT and Telephone
measure is expressed by a two-character alphabeti-
TP-9.
cal abbreviation; e.g., ea, in, pr, etc., and is the basis
1-5. Location of Repair Parts
used to indicate quantities and allowances in
subsequent columns. When the unit of measure
a. This manual contains one cross-reference index
differs from the unit of issue, the lowest unit of issue
(sec IV) to be used to locate a repair part when either
that will satisfy the required units of measure will be
the Federal stock number or reference number
requisitioned.
(manufacturer's part number) is known. The first
e. Quantity Incorporated in Unit. This column
column in the index is prepared in numerical or
indicates the quantity of the item used in the
alphanumeric sequence in ascending order. The
equipment. Subsequent appearances of the same
reference numbers (manufacturer's part number's)
item in the same assembly are indicated by the
are listed immediately following the last listed
letters "REF".
Federal stock number in the index of Federal stock
f. 30-Day DS/GS Maintenance Allowances.
numbers.
NOTE
b. When the Federal stock number or reference
Allowances in GS column are for GS
number is known, follow the procedures given in (1)
maintenance only.
and (2) below.
(1) The repair parts indicated by asterisk entries
(1) Refer to the index of Federal stock numbers
in separate allowance columns for DS and GS
(sec IV) and locate the Federal stock number or
represent those authorized for use at that category
reference number. The FSN and reference number
of maintenance to be requisitioned on an "as
are cross-referenced to the applicable figure and
required" basis, until stockage is based on demand in
item number or reference designation.
accordance with AR 710-2
(2) Refer to the repair parts list (sec II) and locate
(2) Allowance quantities are indicated in the
the figure number (col 10a) and item number or
special tool lists section for special tools, TMDE, and
reference designation (col 10b) as noted in the FSN
other support equipment.
index.
g. 1-Year Allowances Per 100 Equipments/
c. When the figure and item number or reference
Contingency Planning Purposes. Column intention-
designation are known, scrutinize columns 10a and
ally left blank.
10b of the repair parts list (sec II) until the item is
h. Depot Maintenance Allowance Per 100 Equip-
located.
ments. This column indicates opposite the first
d. When the FSN, reference number, figure
appearance of each item the total quantity au-
number, item number and reference designation are
thorized for depot maintenance of 100 equipments.
not known, scrutinize column 3 of the repair parts list
i. Illustration. This column is divided as follows:
(sec II), which is arranged in alphabetical order.
(1) Figure number. Indicates the figure number
1-6. Abbreviations
of the illustration on which the item is shown in TM
Not applicable.
11-2059.
(2) Item number. Indicates the item number or
1-7. Reporting of Equipment Publication
reference designation used to reference the item in
Improvements
the illustration.
1-4. Special Information
The reporting of errors, omissions, and recommenda-
tions for improving this publication by the individual
a. Usable on codes are included in column 3.
4
Previous Page
