TM 11-6625-596-12
Code
Explanation
description of the item required. A part number or other
reference number is followed by the applicable five-digit
X2-
Repair parts which are not stocked.
The
Federal supply code for manufacturers in parentheses.
indicated maintenance category requiring such
repair parts will attempt to obtain same through
d. Unit of Measure, Column 4.
A two-
cannibalization. Where such repair parts are
character alphabetic abbreviation indicating the amount
not
obtainable
through
cannibalization,
or quantity of the item upon which the allowances are
requirements will be requisitioned, with
based; e.g., ft., ea., pr., etc.
supply channels
e. Quantity Incorporated in Unit, Column 5.
G-
Major assemblies that are procured with PEMA
This column indicates the quantity of the item used in
funds for initial issue only as exchange
the TS-716/U. Subsequent appearances of the same
assemblies at DSU and GSU level. These
item in the same assembly are indicated by the letters'
assemblies will not be stocked above DS and
"REF".
OS level or returned to depot supply level.
f.
15-Day
Organizational
Maintenance
(2) Maintenance code indicates the lowest
Allowances, Column 3 of Section II and Column 6 of
category of maintenance authorized to install the listed
Section III.
item. The maintenance level codes are-
(1) The allowance columns are divided
Code
Explanation
into four subcolumns. Indicated in each subcolumn
opposite the first appearance of each item is the total
C .......................... Operator/crew
quantity of items authorized for the number
of
0........................... Organizational maintenance
equipments supported. Subsequent appearances of the
same item will have the letters 'REF "in the allowance
(3) Recoverability code indicates whether
columns. Items authorized for use as required, but not
unserviceable items should be returned for recovery or
for initial stockage, are identified with an asterisk in the
salvage.
Items not coded are expendable.
allowance column.
Recoverability codes are-
(2) The quantitative allowances for
Code
Explanation
organizational level of maintenance represents one initial
prescribed load for a 15-day period for the number of
R-
Applies to repair parts and assemblies which are
equipments supported.
Units and organizations
economically repairable at DSU and GSU
authorized additional prescribed loads will multi- ply the
activities and normally are furnished by sup- ply
number of prescribed loads authorized by the quantity of
on an exchange basis.
repair parts reflected in the density column applicable to
S-
Repair parts and assemblies which are
the number of items sup- ported to obtain the total
economically repairable at DSU and GSU
quantity of repair parts authorized.
activities and which normally are furnished by
supply on an exchange s When items are
(3) Organizational
units
providing
deter- mined by a GSU to be uneconomically
maintenance for more than 100 of these equipments
repair- able, they will be evacuated to a depot
shall determine the total quantity of parts required by
for
evaluation and analysis before final
converting the equipment quantity to a decimal factor by
disposition.
placing a decimal point before the next to last digit of the
T-
High dollar value recoverable repair parts which
number to indicate hundredths, and multiplying * the
are subject to special handling and are issued
decimal factor by the parts quantity authorized in the 51-
on an exchange basis Such repair parts
100 allowance column. Example, authorized allowance
normally are repaired or overhauled at depot
for 51-100 equipments is 40; for 150 equipments
maintenance activities.
multiply 40 by 1.50 or 60 parts required.
U-
Repair parts specifically selected for salvage by
reclamation units because of precious metal
content, critical material, or high dollar value
reusable casings or castings.
b. Federal Stock Number, Column 2, This
column indicates the Federal stock number as- signed
to the item and will be used for requisitioning purposes.
c. Description, Column 3.
This column
indicates the Federal item name and any additional
D-2